Is anyone uses an ATI Videocard under Linux ?

[arlick]

here is my xorg.conf using mesa drivers:

Section "Module"

# This loads the DBE extension module.

    Load        "dbe"  	# Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection

# This loads the font modules
#    Load        "type1"
    Load        "freetype"
#    Load        "xtt"

# This loads the GLX module
    Load       "glx"
# This loads the DRI module
    Load       "dri"

EndSection

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath	"/usr/share/X11/rgb.txt"

    FontPath   "/usr/share/fonts/TTF"
    FontPath   "/usr/share/fonts/OTF"
    FontPath   "/usr/share/fonts/Type1"
    FontPath   "/usr/share/fonts/misc"
    FontPath   "/usr/share/fonts/75dpi/:unscaled"
#    FontPath   "/usr/lib/X11/fonts/local/"
    FontPath   "/usr/lib/X11/fonts/misc/"
    FontPath   "/usr/lib/X11/fonts/75dpi/:unscaled"
    FontPath   "/usr/lib/X11/fonts/100dpi/:unscaled"
    FontPath   "/usr/lib/X11/fonts/Speedo/"
    FontPath   "/usr/lib/X11/fonts/Type1/"
    FontPath   "/usr/lib/X11/fonts/TTF/"
    FontPath   "/usr/lib/X11/fonts/OTF/"
    FontPath   "/usr/lib/X11/fonts/cyrillic/"
    FontPath   "/usr/lib/X11/fonts/75dpi/"
    FontPath   "/usr/lib/X11/fonts/100dpi/"

# The module search path.  The default path is shown here.

#    ModulePath "/usr/lib/dri"
 
EndSection


# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

    Identifier	"Keyboard1"
    Driver	"kbd"

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

#    Option     "Protocol"      "Xqueue"

    Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#    Option	"Xleds"      "1 2 3"

#    Option "LeftAlt"     "Meta"
#    Option "RightAlt"    "ModeShift"


# These are the default XKB settings for Xorg
#    Option "XkbRules"    "xorg"
#    Option "XkbModel"    "pc105"
#    Option "XkbLayout"   "us"
#    Option "XkbVariant"  ""
#    Option "XkbOptions"  ""

#    Option "XkbDisable"

    Option "XkbRules"	"xorg"
    Option "XkbModel"	"pc101"
    Option "XkbLayout"	"es"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

    Identifier	"Mouse1"
    Driver	"mouse"
    Option "Protocol"    "IMPS/2"	# IntelliMouse PS/2
    Option "Device"      "/dev/input/mice"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Option "Protocol"	"Xqueue"

# Mouse-speed setting for PS/2 mouse.

#    Option "Resolution"	"256"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

#    Option "BaudRate"	"9600"
#    Option "SampleRate"	"150"

# Mouse wheel mapping.  Default is to map vertical wheel to buttons 4 & 5,
# horizontal wheel to buttons 6 & 7.   Change if your mouse has more than
# 3 buttons and you need to map the wheel to different button ids to avoid
# conflicts.

    Option "ZAxisMapping"   "4 5 6 7"

# Emulate3Buttons is an option for 2-button mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

#    Option "Emulate3Buttons"
#    Option "Emulate3Timeout"    "50"

# ChordMiddle is an option for some 3-button Logitech mice

#    Option "ChordMiddle"

EndSection


# **********************************************************************
# Other input device sections 
# this is optional and is required only if you
# are using extended input devices.  This is for example only.  Refer
# to the xorg.conf man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice" 
#    Identifier  "Mouse2"
#    Driver      "mouse"
#    Option      "Protocol"      "MouseMan"
#    Option      "Device"        "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball"
#    Driver     "magellan"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball2"
#    Driver     "spaceorb"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen0"
#    Driver     "microtouch"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "1412"
#    Option     "MaxX"          "15184"
#    Option     "MinY"          "15372"
#    Option     "MaxY"          "1230"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen1"
#    Driver     "elo2300"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "231"
#    Option     "MaxX"          "3868"
#    Option     "MinY"          "3858"
#    Option     "MaxY"          "272"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonThreshold"       "17"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "My Monitor"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync   31.5-79.0

#    HorizSync	30-64         # multisync
#    HorizSync	31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync	15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 50-70

Option	    "DPMS" "true"
    

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier	"Standard VGA"
    VendorName	"Unknown"
    BoardName	"Unknown"

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.

#    Chipset	"generic"

# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

    Driver     "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# intalled.

#    BusID      "PCI:0:10:0"

#    VideoRam	256

#    Clocks	25.2 28.3

EndSection

# Device configured by xorgconfig:

Section "Device"
    Identifier  "** ATI Radeon (generic)               [radeon]"
    Driver      "radeon"
    VideoRam    262144
    # Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
    Device      "** ATI Radeon (generic)               [radeon]"
    Monitor     "My Monitor"
    DefaultDepth 24

    Subsection "Display"
        Depth       8
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

 Section "DRI"
    Group "video"
    Mode 0666
 EndSection

[leptom]

The difference between my xorg.conf and yours:

• My device section have: option "DRI" "true"
• My DRI section have not group defined

Try it!

[arlick]

Originally Posted by leptom

The difference between my xorg.conf and yours:

• My device section have: option "DRI" "true"
• My DRI section have not group defined

Try it!

it dont work

direct rendering no

[MAXDDARK]

several days ago I've looked in the wiki for ATI video cards and apparently NONE of the ATI cards supports OpenGL 2.1
OpenGL 2.0 is the limit for them, and the new cards support Directx10.
only the newer Nvidia cards support OpenGL 2.1

so even if we do manage to make the mesa drivers to work, the hardware won't support OpenGL2.1

we are officially screwed !

[surak]

Regnum is fine with OpenGL 2.0

[MAXDDARK]

Originally Posted by surak

Regnum is fine with OpenGL 2.0

yes it is.
But I recall you saying that in order to see all the Directx features with OpenGL in this game, we must have OpenGL 2.1

so what are we missing ?

[surak]

That was a misunderstanding. OpenGL 2.0 has all the capabilities needed to show the game at full detail.

[Smiley2k7]

I've got Raedeon 1300/1550 but not under Linux :P but under DirectX

[arlick]

Originally Posted by surak

That was a misunderstanding. OpenGL 2.0 has all the capabilities needed to show the game at full detail.

my problem is if i wanna play i need active "force secutiry mode", without it i always crash before start the game.

my opengl version with propietary drivers are: 2.0.66...

[surak]

That's because ATI propietary drivers crashes compiling shaders. I'm considering to disable shader support for ATI under linux (until drivers are fixed)